First, start on the right side corner of your dash bezel It seems to have a better finger hold and pull. Remove the electrical connections to the starter and label for replacement. The deck should now slide out of the encasing through the front away from the dashboard. Raise the cover over the wiper arm retaining nuts. Remove the wheel and tire assembly. There are six clips on the trim plate.
When buying a New Alternator have them check it before taking it home? They manufacture and sell 5w20 synthetic. Would be able to send me the wiring diagrams to help me pull this off? The driver's side door should be the same, except for the mirror switch which needs to be unplugged. Thank you in advance for any advice you can provide. Be careful the filter is pressurized. You might have to move it up a bit more than the control would.
Remove the round rubber stopper from behind the assembly to… Buy a Chiltons service manual and it will help alot. You might even find that it's not as hard as you'd expected. You'll save money when you install it yourself — and we can help you do it Installing car stereo gear yourself is a satisfying experience. Slowly pull out radio until you can reach the back side. The dash bezel is held in be snap clips. Disclaimer: -Some of our units used engine, transmission, axle, etc. Tap them with a rubber mallet and try spraying some silicone spray to loosen them up.
On some front-wheel drive cars, upper mounts torque struts also control the fore and aft movement of the engine during acceleration. Remove the cotter pin and castellated nut from the upper ball joint. If you are planning to install an aftermarket radio, buy yourself a radio wiring hardness that will fit into the factory wiring hardness. Unplug antenna and wiring harness. Basically, is there such an animal of a replacement where no functionality will be lost? Passenger and driver side airbags 4. You will need to purchase an after market wiring kit made for the truck. The plastic holder should pull out of the door.
Disconnect the negative battery cable. Most motor mounts are relatively simple in design and consist only of metal attachment plates and large rubber insulator blocks… You need a T10 torx tip on straight multi bit driver ,turn mirror assembly out away from door. Unplug the wires and there you go! With a little elbow grease and patience they will eventually come off. It's tricky because the edges get caught on the surrounding structures, but it will slide out. Be careful of the courtesy light when removing the panel - give the light a quarter turn counter-clockwise from the rear to remove it from the door panel. Pull it off, remove screws around radio and there you have it.
In my Wrangler there was a bar that was attached to the back of the stereo and to two bolts on the inside upper part of the dash. I suggest pioneer, and replace the speakers while you are at it too. Pull up on the door panel to remove it. Then remove the ashtray by pulling it out. Raise and safely support the vehicle.
Don't worry it's fairly sturdy. They'll probably know or have the tool to take it out, if one is needed, and most likely they'll do it free of charge, Ford does. The 3rd bolt is between the bottom and top bolts. Now, to remove the loose bezel out from around the steering wheel, you will then have to tilt the wheel all the way down. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped.
Avoid touching the glass envelope. This is all there is to it:. . Match mark the wiper arms to the pivot for reinstallation. I do remember hearing a mechanic say that the way the original actuator came out is how the new… Oxygen Sensor There are actually 4 O2 sensors on your truck.
If you are installing an after market radio. Now pry up on both sides of the triangular panel and pull it loose. Then start pulling your way around the whole b … ezel until all is popped loose. Always disconnect the negative batterry cable. Remove the the heater control assembly.
HeaterTreater is the world's leading company for aftermarket blend door fixes and has… Windshield Wiper Blade and Arm Front 1. We stock a large quantity of Ford radio products and can provide efficient and affordable radio repair services. Raise and support the vehicle. The mounts isolate engine and transmission from the chassis so vibrations and noise are not transmitted to the rest of the vehicle. There are clips all around the perimeter.